r/BdsmDIY

I redesigned the clamps in my last post. in the last photo you can see them. the new design is on the left and the old design is on the right.

I currently have them in my shop at the moment. I currently only ship around the US. sorry international friends, I'll open international shipping one day.

I recently ordered more of these clamps so i could make these. they're not something that I'll have in my shop at all times, because the clamps are pricey. I may do a different design at some point.

Pretty happy with how it turned out, I also learned a lot in the process.

I've always liked the idea of having restraints on the bed, but I often find them quite annoying when it comes to putting them on the bed, taking them off, and keeping them hidden if needed. I recently made an automatic under the bed restraint system that turned out really nice, fixed alot of the above issues, and also allowed for more play options.

This works in a very similar fashion to a seatbelt, pull out all the slack and then a ratchet engages so you can't get any slack until the belt is retracted all the way. This works that exact same way. I made it so this can easily mount to the bottom of your bed frame so that it is out of sight and if bound on top of the bed, impossible to reach and disengage. The spool holds 5 feet of paracord, plenty for bedroom bondage.

Since these automatically pull in the slack it makes it great for producing tight bondage. These also work great for self bondage since this will automatically tighten once all the slack is pulled out. There is a switch on the outside of the housing that can be used to let out slack if needed. I found this to be a good feature at the end of the session to quickly and easily loosen the person that is bound.

The mount that I made easily slides into my bed frame and once the mattress is on top of it it can't go anywhere. I also made on where you could screw it to a flat surface. There is also a hole in the housing so that the device could be tied to an eye bolt or anchored to anything.

The design uses a cheap recoil spring to make it work. I like the idea of making everything 3d printable, but sometimes it is nice to incorporate actual metal products to make somethings so much better. This whole project was alot more complicated that I originally thought it was going to be. The design uses a small planetary gearbox to be able to let the spool spin 5 times before ratcheting. After 5 spins the ring gear hits a lever on the pawl to engage the ratchet and pawl system, and then the recoil spring winds everything back up.

This is a huge improvement over what we had in the past. I think there are a lot of other scenarios that could benefit from this type of system. I think this might be very advantageous to use in self bondage as long as you have a reliable release mechanism.

Delrin cane shaft is 18" in length and 3/8" in diameter. Approximately 23" overall. Handle length is approximately 5-1/4". Tip has been rounded for added safety.

Shaft is 32" long and 3/8" diameter delrin with a handle turned from Honduran rosewood with a copper ferrule. 38-1/2" overall length. This thing would be like getting hit with a car antenna.

I recently acquired a Bambu Lab P1S and was disappointed by the lack of functional locking collars, so a Friday evening project turned into a basic locking collar with some multi-color accents (and a few more evenings). Heavily inspired by existing designs, two halves, a hinge at the back, and full assembly without needing to go to the hardware store. Not Print-in-Place, I prefer smaller parts so I don't have too much waste if the printer messes up.

I initially started with a simple oval ring and decided to add sharp elements inside for discomfort, but they are barely noticeable, even though they look intimidating. Then played around with some decoration for a few spikes.

I haven't done a lot of CAD design before this, so I'm quite happy with the result. Wish I had another design for the locking tabs, since it annoys me that I need a separate shim piece, but without it a loose padlock would lead to a slight gap where skin could get pinched. Printing requires some manual support adjustments. Bambu Studio likes to place supports in lots of places where they are not needed, like in the spike holes or the channel where the hinge pin goes into. Had to manually paint no-support zones and restrict supports to the print plate.

I definitely want to experiment with a more integrated locking mechanism. The prints I did were surprisingly strong when closed (using 20% infill). Not sure where to go beyond that.

Put the STL files on Cults3D with common sizes: https://cults3d.com/en/3d-model/naughties/spiked-locking-collar

Happy to get some feedback on the build itself, pretty new to 3D printing and even newer to sharing files, so if something is annoying/doesn't work for you, let me know.

I really liked the look of the magbound system but couldn't justify the cost so managed to build an almost identical Maglock for under £50!

The magnet is rated to 50kg,though it is a little lower thanks to the plastic sheet covering the face of the magnet. This is needed to deal with residual magnetism.

3d printed the housing to make sure everything aligns properly and use either a cheap aliexpress usb timer or a USB smart switch to allow for long distance control of my bondage.

I've perfected my toy lol

Got this bench about 70% done then realized I never bought the pocket hole jig I needed for it and still need to order the marine vinyl. Starts as a very sturdy saw horse then gets the legs rest.

first DIY Furniture next up is a spanking bench!